Solar Panels During Power Outage Events: Why They Shut Off and How to Keep Power On
The sun was out, the panels were clean, and the house still went dark. That's not a fault. It's a safety rule, and there are good ways to work with it.
Published · Updated
10 min read

Most grid-tied solar panels during power outage events shut off on purpose. Their inverters need a live grid signal and disconnect when it disappears, which protects utility crews working on the lines. To keep power on, a home needs a battery or other backup with equipment that isolates the house from the grid.
- Standard grid-tied inverters shut down when the grid goes down, even in full sun.
- This anti-islanding behavior keeps solar power from flowing onto lines crews believe are dead.
- A battery system with grid-forming capability and automatic isolation can keep chosen circuits running.
- A critical loads panel concentrates backup on the circuits that matter, which stretches battery hours.
- California's interconnection rules, known as Rule 21, govern how home generation connects to the grid.
You've had solar since 2018, and during the last shutoff your Novato home went as dark as your neighbor's. It feels like the system failed. It didn't. Solar panels during power outage events are designed to stop sending power, and understanding why is the first step to getting the backup you assumed you already had.
This deep dive explains what happens inside a solar system when the grid drops, why the rules are written that way, and what it takes to keep lights, the fridge and the internet running. We'll look at inverters, batteries, critical loads panels and how a generator fits in, with the numbers behind each choice.
If you're planning new panels or adding storage, our solar panel installation page covers the electrical side of both.
Part of our guide to Solar Panel Installation. It covers solar electrical work, storage integration and service capacity.
Why do solar panels during power outage events shut off?
Solar panels during power outage events shut off because standard grid-tied inverters need the grid's signal to operate. According to the U.S. Department of Energy, grid-following inverters will disconnect and shut down during disruptions, since they have no grid to follow.
When a home's generator or solar system keeps powering local wires after the utility grid goes down. It's dangerous for line crews, so grid-tied systems are designed to prevent it.
An inverter that matches the grid's voltage and frequency to deliver solar power. Without a grid signal to follow, it shuts down.

That design is intentional. When the grid goes down, utility crews treat the lines as de-energized while they repair them. A solar system still pushing power onto those wires could shock someone who believes the line is dead. The inverter's shutdown keeps that from happening.
Your panels still make DC power in the sun. The inverter simply refuses to convert and deliver it without the grid, and most basic systems have nowhere else to send it. That's why a plain grid-tied system offers no backup at all, no matter how sunny the day.
Many owners only learn this during their first shutoff, because nothing in a normal day reveals it. The panels produce, the meter spins backward, and the bill drops. The missing piece only shows up when the grid does.
What is anti-islanding protection, and who does it protect?
Anti-islanding protection is the inverter function that detects a grid outage and stops exporting power within moments. It protects line workers first, and it also protects your equipment from unstable power when the grid returns.
How anti-islanding protection is required in California
The rules for connecting home generation to the grid live in a tariff called Rule 21. The California Public Utilities Commission describes Rule 21 as the interconnection, operating and metering requirements for generation facilities connecting to a utility's distribution system. Inverters certified for those requirements include anti-islanding behavior.
The same rule protects your home, too. When grid power comes back, it can return with surges or unstable voltage. Inverters wait for steady power before they reconnect. That short delay is normal, and it's one reason solar often comes back a few minutes after the lights do.
That's why you can't simply flip a switch to keep solar running in an outage. Any system that powers the house while the grid is down has to physically isolate the home from the utility first. That isolation is the job of a backup gateway, transfer equipment or a battery inverter designed for it.
- Detects loss of grid voltage or frequency and stops exporting.
- Waits for stable grid power before reconnecting.
- Works alongside isolation equipment when backup is installed.
A Novato home with rooftop solar went dark during a shutoff on a sunny day, because its grid-tied inverter is designed to stop when the grid stops.
Add a battery with isolation equipment and a grid-forming inverter, and move essential circuits to a critical loads panel so storage lasts through the night.
The fridge, lights and internet stay on, and solar recharges the battery each sunny day. This isn't for owners whose outages are rare and brief. A small portable power station may serve them better.
How does solar battery backup keep the lights on?
Solar battery backup keeps the lights on by isolating your home from the grid during an outage, then powering chosen circuits from the battery while the panels recharge it in daylight. The battery's inverter creates its own stable signal, so the solar inverter has something to follow.
What a grid-forming inverter adds
A grid-forming inverter can create voltage and frequency on its own, instead of following the utility. The Department of Energy notes that grid-forming inverters can produce a grid signal and even help restart a system from a blackout. In a home backup setup, that capability lets solar keep working inside the isolated house.
Battery hours depend on what you ask the system to carry. A refrigerator, lights, internet and a few outlets add up to a modest load. Add an electric range, a well pump or central air, and those same kilowatt-hours disappear fast. That's why most solar battery backup designs start with a short list of circuits.
Our guides to solar and battery electrical integration and solar battery integration explain the wiring and equipment in more depth.
We'll design battery integration around your existing inverter and the circuits you can't live without.
Should backup run through a critical loads panel or the whole home?
A critical loads panel moves your most important circuits into a separate subpanel that the battery powers during an outage, while whole-home backup keeps everything connected and relies on careful energy use. Each approach suits different batteries, homes and habits.
| Approach | How it works | Good fit for | Trade-off |
|---|---|---|---|
| Critical loads panel | Chosen circuits move to a backed-up subpanel | Smaller batteries and long outages | Other circuits stay dark |
| Whole-home backup | The whole panel is isolated and backed up | Larger storage and engaged owners | Big loads can drain the battery quickly |
| Whole-home with load control | Whole panel, with large loads shed automatically | Homes with electric cooking or heat pumps | More equipment to plan and install |
Choosing circuits for a critical loads panel
Most families pick the refrigerator, a few lighting circuits, the internet and router, bedroom outlets and any medical equipment. Gas furnace fans and garage doors are common additions. Electric heat, dryers and ranges usually stay off the list unless the battery is large.
Test the plan once it's installed. Have your installer simulate an outage on a sunny afternoon, then live with the backed-up circuits for an hour. You'll learn which lights you miss and which outlets you need. It's far better to learn that on a calm day than during a windy night in a real shutoff.
If you're starting from scratch, our guide to getting your Marin home solar-ready explains how panel layout and spare capacity make later storage easier.
How long can solar recharge a battery during a PSPS?
Solar can recharge a battery every sunny day of a shutoff, which is why solar plus storage handles multi-day events better than a battery alone. How much it recovers depends on the array's size, the season, shading and smoke.
Shutoffs are often multi-day, wind-driven events. The California Public Utilities Commission explains that utilities may turn off power to reduce fire risk during strong winds and dry conditions. In Novato and Petaluma, those days can be clear and sunny or hazy with smoke, so plan for both.
Fall days are shorter, and smoke can cut output noticeably. Treat any recharge estimate as an upper-end range, not a promise. A battery sized to carry essential loads overnight, with solar topping it up by day, is the practical goal.
New construction is moving this way by design. The California Energy Commission requires new single-family homes with one or two dwelling units to be battery-storage ready under the 2022 Energy Code, so wiring and panel space are planned for storage from the start.
Can a generator work with solar panels during power outage events?
A generator can work with solar panels during power outage events, but it has to be integrated correctly so the generator, the battery and the solar inverter don't fight each other. Some battery systems accept a generator input, while others need separate transfer equipment and careful settings.
- 01Identify your inverter
Note the brand, model and whether it's a string inverter or microinverters.
- 02List essential circuits
Decide what must run during an outage and estimate the load.
- 03Choose storage and isolation
Pick a battery and gateway that work with your inverter and panel.
- 04Plan the generator role
Decide whether a generator backs up the battery, and how it connects.
- 05Permit and interconnect
Update the interconnection with your utility and pass inspection.
Talk with a licensed C-10 electrician about batteries, critical loads panels and safe isolation. Request your estimate or call our Novato office.
- Rule 21
- California's interconnection tariff that sets how generation facilities, including home solar, connect to the utility distribution system.
- Backup gateway
- Equipment that disconnects a home from the grid during an outage so a battery can safely power it.
- Critical loads panel
- A subpanel holding the circuits a backup system powers during an outage.
- Grid-forming inverter
- An inverter that can create its own voltage and frequency, so other equipment can follow it without the grid.
Frequently asked questions
Why doesn't my solar work when the power goes out?
Most home solar stops during an outage because grid-tied inverters need a live grid signal and are designed to shut down when it disappears, which keeps power off lines that utility crews are repairing. That's anti-islanding protection. It's working as intended. To keep power on, you need a battery and isolation equipment. An electrician can tell you what fits your inverter.
Can I add solar battery backup to an existing system?
Yes, many existing systems can add solar battery backup, though the right battery and gateway depend on your inverter type, panel layout and how the system is interconnected with the utility. Some setups pair easily. Others need equipment changes. An updated interconnection is usually part of the job. Start with a site assessment.
What does a grid-forming inverter do during an outage?
A grid-forming inverter creates its own voltage and frequency, so during an outage it can power an isolated home and give solar inverters a signal to follow, letting the panels keep producing. Grid-following inverters can't do that alone. Most battery backup systems use grid-forming capability. Isolation from the utility happens first. That keeps crews safe.
Which circuits should go on a critical loads panel?
Most critical loads panels include the refrigerator, a few lighting circuits, internet equipment, bedroom outlets and any medical devices, while large loads like electric ranges, dryers and electric heat stay off unless storage is large. Keep the list short. Short lists stretch battery hours. A furnace fan or garage door is a common addition. Your electrician can measure the loads first.
How much does it cost to add a battery to my solar system?
The cost of adding a battery depends on the storage size, whether you choose a critical loads panel or whole-home backup, the equipment your existing inverter needs, panel work, permits and the interconnection update. Larger storage and whole-home setups cost more. Older panels may need upgrades. We quote after reviewing the inverter and panel. That keeps the design matched to your home.
Is anti-islanding protection required for home solar in California?
Yes, home solar connected to the grid must meet interconnection requirements under California's Rule 21, and inverters certified for those requirements include anti-islanding protection that stops exporting power when the grid goes down. It protects line workers. It also protects equipment when power returns. Backup systems work with it, not around it. Isolation equipment is part of every safe backup design.
Will solar panels during power outage events recharge a battery?
Yes, in a properly designed backup system, solar panels during power outage events can recharge the battery each day, because the isolated home gives the solar inverter a stable signal from the battery. Output depends on sun, season, shade and smoke. Fall days are shorter. Plan for less than peak production. Size the battery to carry essential loads overnight.
Grid-tied solar shuts off in an outage to protect line crews, by design. A battery with isolation equipment and a grid-forming inverter turns solar into backup, and a short list of critical circuits makes the stored energy last.

Founder of Healthcare Marketing Group and author of The Ultimate Guide to Digital Marketing. Previously led a digital marketing company with 8,000+ clients. Writes on local-service SEO and E-E-A-T content strategy.

Alex founded Towery Electric in Novato in 2014 after years wiring homes in San Francisco. He reviewed this article for technical accuracy on Oct 16, 2026.
- ✓ Licensed-contractor reviewed
- ✓ Primary sources cited
- ✓ Updated when code changes
We research every article from primary sources, including government safety agencies, code bodies and utility programs, and a licensed C-10 electrical contractor reviews it before it’s published. Our editorial standards →
Sources
- U.S. Department of Energy, Solar Energy Technologies Office. Solar Integration: Inverters and Grid Services Basics.
- California Public Utilities Commission. Rule 21 Interconnection.
- California Public Utilities Commission. Public Safety Power Shutoffs (PSPS).
- California Energy Commission. 2022 Single-Family Electric Ready requirements (2022).
Changelog: Oct 16, 2026: first published after technical review by Alex Towery, C-10 #989290.
Disclaimer: This article is general educational information, not a site-specific electrical assessment or legal advice. Codes, utility programs and permit rules change, and every home’s wiring is different. Electrical work in California should be done by a licensed C-10 contractor with the required permits.
When to call: Call a licensed electrician before adding a battery or generator to a solar home, or if anyone has suggested bypassing the inverter's shutdown. If you see smoke, sparks or fire, leave the area and call 911 first.